RENEWABLE ENERGY
Alternative Energy Sources
World-wide, with the exception of coal, which has known reserves that will last a couple of centuries, the known reserves of oil are expected to be exhausted in your lifetime...
Clearly, alternative energy sources are needed for the future
U.S. Energy Consumption
The four primary consumers of energy in the U.S. in 2007 were
Industrial 32%
Transportation 28%
Residential 22%
Commercial 18%
93% of the energy generated and used in the U.S. are from nonrenewable resources
We will look at:
Solar energy
Geothermal power
Hydropower
Tidal Power
Ocean thermal energy conversion
Wind energy
Biomass
Solar Energy
The Sun is free (nobody owns or controls it)
In principle, the amount of solar energy that reaches the Earth’s surface could provide for all human energy needs forever
The distribution of solar energy over the continental U.S. in watts per square meter
The desert regions of the southwest U.S. receive the most sunlight
Clean Solar Energy
Solar energy is clean energy
It produces no hazardous solid, liquid or gas wastes
It does not create water or air pollution
The two areas in which solar energy can make the greatest contribution are in space heating and in the generation of electricity
These are uses that account for two-thirds of U.S. energy consumption
Solar Heating
The simplest approach to solar heating is passive-solar heating
The building design should allow the maximum amount of sunlight to stream in through south and west windows during the cooler months
This heats the house and materials inside
Trees can be positioned to shade the house in summer
Wide eaves can shade windows in summer, but allow winter sunlight to enter
Drapes and shutters can insulate window areas in winter
It has been estimated that 40 to 90% of most homes’ heating requirements could be supplied by passive-solar heating systems
100% solar homes have been built, but such homes usually cost many tens of thousands of dollars more to build
Retrofitting older homes to be solar efficient can be too costly
Over insulation can aggravate indoor pollution
Solar Electricity
Direct production of electricity using sunlight is accomplished using photovoltaic cells, also called solar cells
They have no moving parts and are “clean” energy
They are used to power the space station and to provide electricity in remote areas on Earth
A major limitation is cost, which greatly exceeds the cost of producing electricity using fossil fuels or nuclear power
The best solar cells are only 20% efficient and only provide 50 watts of electricity per square meter of cell size
A 100 watt light bulb would require 2 square meters of solar cells
And a 100-megawatt power plant would require 2 square kilometers (0.78 square miles) of solar cells
This represents a major use of land and resource, which would use far more steel and concrete than a fossil fuel power plant
Storing Solar Electricity
In a solar energy home, extra electricity is stored in batteries for later use
This work well for one house
Unfortunately, no wholly practical technology has been developed to store large amounts of electricity, despite advances in batteries
Some possible schemes for storing the energy of solar generated electricity include breaking up water into oxygen and hydrogen to burn later as fuels
Also pumping water to an elevated reservoir for later use as hydroelectric power generation
Currently, solar energy provide less that 0.5% of the U.S. power needs, but even with existing technology, it could provide up to 15%
Geothermal Power
Magma rising from the mantles brings unusually hot material near the surface
Heat from the magma, in turn, heats any groundwater
This is the basis for generating geothermal energy
The steam and/or hot water is used to create electricity or for heating
Geothermal Power Plants
Worldwide, there are now about 40 geothermal power plants, especially in Japan, Mexico and the Philippines
Note that most geothermal power plants are built along plate tectonic boundaries
Clearly, alternative energy sources are needed for the future
U.S. Energy Consumption
The four primary consumers of energy in the U.S. in 2007 were
Industrial 32%
Transportation 28%
Residential 22%
Commercial 18%
93% of the energy generated and used in the U.S. are from nonrenewable resources
We will look at:
Solar energy
Geothermal power
Hydropower
Tidal Power
Ocean thermal energy conversion
Wind energy
Biomass
Solar Energy
The Sun is free (nobody owns or controls it)
In principle, the amount of solar energy that reaches the Earth’s surface could provide for all human energy needs forever
The distribution of solar energy over the continental U.S. in watts per square meter
The desert regions of the southwest U.S. receive the most sunlight
Clean Solar Energy
Solar energy is clean energy
It produces no hazardous solid, liquid or gas wastes
It does not create water or air pollution
The two areas in which solar energy can make the greatest contribution are in space heating and in the generation of electricity
These are uses that account for two-thirds of U.S. energy consumption
Solar Heating
The simplest approach to solar heating is passive-solar heating
The building design should allow the maximum amount of sunlight to stream in through south and west windows during the cooler months
This heats the house and materials inside
Trees can be positioned to shade the house in summer
Wide eaves can shade windows in summer, but allow winter sunlight to enter
Drapes and shutters can insulate window areas in winter
It has been estimated that 40 to 90% of most homes’ heating requirements could be supplied by passive-solar heating systems
100% solar homes have been built, but such homes usually cost many tens of thousands of dollars more to build
Retrofitting older homes to be solar efficient can be too costly
Over insulation can aggravate indoor pollution
Solar Electricity
Direct production of electricity using sunlight is accomplished using photovoltaic cells, also called solar cells
They have no moving parts and are “clean” energy
They are used to power the space station and to provide electricity in remote areas on Earth
A major limitation is cost, which greatly exceeds the cost of producing electricity using fossil fuels or nuclear power
The best solar cells are only 20% efficient and only provide 50 watts of electricity per square meter of cell size
A 100 watt light bulb would require 2 square meters of solar cells
And a 100-megawatt power plant would require 2 square kilometers (0.78 square miles) of solar cells
This represents a major use of land and resource, which would use far more steel and concrete than a fossil fuel power plant
Storing Solar Electricity
In a solar energy home, extra electricity is stored in batteries for later use
This work well for one house
Unfortunately, no wholly practical technology has been developed to store large amounts of electricity, despite advances in batteries
Some possible schemes for storing the energy of solar generated electricity include breaking up water into oxygen and hydrogen to burn later as fuels
Also pumping water to an elevated reservoir for later use as hydroelectric power generation
Currently, solar energy provide less that 0.5% of the U.S. power needs, but even with existing technology, it could provide up to 15%
Geothermal Power
Magma rising from the mantles brings unusually hot material near the surface
Heat from the magma, in turn, heats any groundwater
This is the basis for generating geothermal energy
The steam and/or hot water is used to create electricity or for heating
Geothermal Power Plants
Worldwide, there are now about 40 geothermal power plants, especially in Japan, Mexico and the Philippines
Note that most geothermal power plants are built along plate tectonic boundaries
How the geothermal energy is used depends on the temperature of the water
Three types of power plants are used to generate power from geothermal energy
Dry steam
Flash
Binary
Types of Geothermal Power
Dry steam plants take steam out of the ground and uses the steam to turn a turbine that spins a generator
This was first done in Italy in 1904
Flash plants take super heated water, usually at temperatures over 200°C, out of the ground, allowing it to boil as it rises to the surface, then separates the steam from the water and uses the steam to turn a turbine generator
In binary plants, the hot water flows through heat exchangers, boiling an organic fluid that spins the turbine
For all three types of power plants, the condensed steam and remaining geothermal fluid are injected back into the hot rock to pick up more heat
This is why geothermal energy is viewed as sustainable
It is also very “clean”
Only produces steam
The largest U.S. geothermal power plant is The Geysers in California (it uses dry steam)
By 1989, a total of 10 billion watts of electricity was being produced by The Geysers and six other plants in the U.S.
By the end of 2005 worldwide use of geothermal energy for electricity had reached 9.3 billion watts, with an additional 28 billion watts used directly for heating
Even if the geothermal water is not as hot as steam, the warm water can be used to heat buildings, home and even greenhouses
This is routinely done in Russia and Iceland
Limitations
Each geothermal field can only be used for a period of time, a few decades, before heat extraction is seriously reduced
Simply put, you can take hot water out of the ground faster than it can be renewed (even if you pump the water back into the ground)
For example, steam pressure at The Geysers has declined rapidly over recent years
It peaked at over 2 billion watts by 1991, but now in 2011 produces about 0.7 billion watts
Hydropower
One-third (33%) of all power plants in the U.S. are hydroelectric, but they only generate 6% of U.S. electricity needs
Water use for generating hydroelectric power is totally dependent on the available water (duh!!)
The Glen Canyon Dam in Utah is the classic example of building too big of dam for not enough water
Hydropower is a very clean, pollution-free, renewable energy source
The water is not consumed, but rather simply passes thru the generating equipment, and since several dams may occur along the same river, the water can be reused and reused
If every stream and river in America was dammed to generate power, you still only provide 20% of current U.S. power needs
There are about 1000 dams in the U.S. and there is very little prospect of building any new ones
In fact, some older dams have been removed, such as the 162 years old Edwards Dam in Maine
Tidal Power
All large bodies of water, including the oceans and large lakes, have tides
Tidal power captures the energy contained in moving water mass due to tides
Two types of tidal energy can be extracted:
Kinetic energy of currents between ebbing and surging tides
Potential energy from the difference in height (or head) between high and low tides
You can use the flowing water between low and high tides to generate electricity, similar to hydropower
Turbines can be place on the ocean floor, for example at the entrance of a bay, where the flowing water can turn the fan to generate electricity
Another option is to use under water turbines, which is like an underwater wind farm
This is currently being tested offshore of Scotland’s Orkney Islands
The ebbing and surging tidal flows turn 100 foot propellers, which each produce 1 megawatts of electricity
OTEC
Ocean energy thermal conversion (OTEC) is a new, clean technology that is still in the developmental stage
It exploits the temperature difference between warm surface water and the cold water at depth to run a “heat engine”
A heat engine is a device placed between a high temperature reservoir and a low temperature reservoir that produces energy
Either the warm water is used directly to run a turbine, or the heat is used to vaporize a working fluid (ammonia) which runs the turbine
The cold water is used to chill down the water or vapor
Drinkable, distilled fresh water is a by-product
The temperature difference must be at least 40°F (22°C) year round, which is only found near the equator
So this emerging technology is best for tropic islands
Wind Energy
The wind is free, commonly available and can provide clean, pollution-free energy
Today’s wind-turbines are very high tech
In most places, the cost of commercial wind power on a large scale is not now economically competitive with conventionally generated electricity
One important factor is that with a doubling of wind speed, power output increases by a factor of 8
The numbers indicate the percentage of 1990 regional electricity demand that full utilization of wind energy could meet
Clearly, the great plains have significant wind energy potential
U.S. wind power capacity from 1981 to 2002
Three types of power plants are used to generate power from geothermal energy
Dry steam
Flash
Binary
Types of Geothermal Power
Dry steam plants take steam out of the ground and uses the steam to turn a turbine that spins a generator
This was first done in Italy in 1904
Flash plants take super heated water, usually at temperatures over 200°C, out of the ground, allowing it to boil as it rises to the surface, then separates the steam from the water and uses the steam to turn a turbine generator
In binary plants, the hot water flows through heat exchangers, boiling an organic fluid that spins the turbine
For all three types of power plants, the condensed steam and remaining geothermal fluid are injected back into the hot rock to pick up more heat
This is why geothermal energy is viewed as sustainable
It is also very “clean”
Only produces steam
The largest U.S. geothermal power plant is The Geysers in California (it uses dry steam)
By 1989, a total of 10 billion watts of electricity was being produced by The Geysers and six other plants in the U.S.
By the end of 2005 worldwide use of geothermal energy for electricity had reached 9.3 billion watts, with an additional 28 billion watts used directly for heating
Even if the geothermal water is not as hot as steam, the warm water can be used to heat buildings, home and even greenhouses
This is routinely done in Russia and Iceland
Limitations
Each geothermal field can only be used for a period of time, a few decades, before heat extraction is seriously reduced
Simply put, you can take hot water out of the ground faster than it can be renewed (even if you pump the water back into the ground)
For example, steam pressure at The Geysers has declined rapidly over recent years
It peaked at over 2 billion watts by 1991, but now in 2011 produces about 0.7 billion watts
Hydropower
One-third (33%) of all power plants in the U.S. are hydroelectric, but they only generate 6% of U.S. electricity needs
Water use for generating hydroelectric power is totally dependent on the available water (duh!!)
The Glen Canyon Dam in Utah is the classic example of building too big of dam for not enough water
Hydropower is a very clean, pollution-free, renewable energy source
The water is not consumed, but rather simply passes thru the generating equipment, and since several dams may occur along the same river, the water can be reused and reused
If every stream and river in America was dammed to generate power, you still only provide 20% of current U.S. power needs
There are about 1000 dams in the U.S. and there is very little prospect of building any new ones
In fact, some older dams have been removed, such as the 162 years old Edwards Dam in Maine
Tidal Power
All large bodies of water, including the oceans and large lakes, have tides
Tidal power captures the energy contained in moving water mass due to tides
Two types of tidal energy can be extracted:
Kinetic energy of currents between ebbing and surging tides
Potential energy from the difference in height (or head) between high and low tides
You can use the flowing water between low and high tides to generate electricity, similar to hydropower
Turbines can be place on the ocean floor, for example at the entrance of a bay, where the flowing water can turn the fan to generate electricity
Another option is to use under water turbines, which is like an underwater wind farm
This is currently being tested offshore of Scotland’s Orkney Islands
The ebbing and surging tidal flows turn 100 foot propellers, which each produce 1 megawatts of electricity
OTEC
Ocean energy thermal conversion (OTEC) is a new, clean technology that is still in the developmental stage
It exploits the temperature difference between warm surface water and the cold water at depth to run a “heat engine”
A heat engine is a device placed between a high temperature reservoir and a low temperature reservoir that produces energy
Either the warm water is used directly to run a turbine, or the heat is used to vaporize a working fluid (ammonia) which runs the turbine
The cold water is used to chill down the water or vapor
Drinkable, distilled fresh water is a by-product
The temperature difference must be at least 40°F (22°C) year round, which is only found near the equator
So this emerging technology is best for tropic islands
Wind Energy
The wind is free, commonly available and can provide clean, pollution-free energy
Today’s wind-turbines are very high tech
In most places, the cost of commercial wind power on a large scale is not now economically competitive with conventionally generated electricity
One important factor is that with a doubling of wind speed, power output increases by a factor of 8
The numbers indicate the percentage of 1990 regional electricity demand that full utilization of wind energy could meet
Clearly, the great plains have significant wind energy potential
U.S. wind power capacity from 1981 to 2002
The U.S. remains the world leader in wind energy, but Europe has embarked on an very ambitious wind-power development program
It is predicted that by 2030, wind energy will supply at least twice the electricity it does now
Biomass Energy
Biomass energy is derived from organic matter
Stoves that burn wood are the classic example
In fact, there had been a 20-25% increase in the use of wood stoves over the past several decades
Biomass Fuels or Biofuels
Biofuels differ from other renewable energy sources, such as wind, hydroelectric, geothermal and solar, as they are primarily used in the transportation sector and are derived from recently living matter, both plant and animal
Ethanol Fuel
Ethanol fuel is a biofuel alternative to gasoline, which is gaining popularity world-wide
Car engines can be designed to run on 10%, 50% even 100% pure ethanol
It is cleaner burning than gasoline
Worldwide, the use of ethanol is rapidly increasing
Automotive ethanol capabilities vary widely country to country, but most spark-ignited gasoline style engines will operate well with mixtures of up to 10% ethanol
Brazil is the world leader in ethanol fuels
Ethanol fuel is produced from sugar cane in Brazil, which is a more efficient source of fermentable carbohydrates than corn as well as much easier to grow and process in the tropical climate
“E” Numbers
Ethanol fuel mixtures have "E" numbers which describe the percentage of ethanol in the mixture by volume, for example, E85 is 85% ethanol and 15% gasoline
Low ethanol blends, from E5 to E25, are also known as gasohol, though internationally the most common use of the term gasohol refers to the E10 blend
Gasohol
E10 gasohol is becoming more commonly found at gas stations in the U.S. (Tennessee is way behind)
As the “10” indicates it is made from a mixture of
gasoline (90%) and ethanol (10%)
Gasohol has higher octane, or antiknock, properties than gasoline and burns more slowly, more cooler, and more completely, resulting in reduced emissions of some pollutants
UT & Switchgrass
The UT Biofuels Initiative has started testing the use of switchgrass, which is believed to offer a greater ethanol yield than corn in a temperate climate, such as in Tennessee
The project represents the culmination of years of corporate research and development and a highly touted $40.7 million investment from the state of Tennessee to build a plant for demonstrating technology developed by DuPont Danisco Cellulosic Ethanol
Alternative Energy Sources
Most of the world still relies very heavily on fossil fuels, but slowly but surely, attention is being diverted to alternative energy
Energy use in the future will not be dominated by a single source
The most important aspects of most alternative energy sources is that they promise clean, pollution-free energy
It is predicted that by 2030, wind energy will supply at least twice the electricity it does now
Biomass Energy
Biomass energy is derived from organic matter
Stoves that burn wood are the classic example
In fact, there had been a 20-25% increase in the use of wood stoves over the past several decades
Biomass Fuels or Biofuels
Biofuels differ from other renewable energy sources, such as wind, hydroelectric, geothermal and solar, as they are primarily used in the transportation sector and are derived from recently living matter, both plant and animal
Ethanol Fuel
Ethanol fuel is a biofuel alternative to gasoline, which is gaining popularity world-wide
Car engines can be designed to run on 10%, 50% even 100% pure ethanol
It is cleaner burning than gasoline
Worldwide, the use of ethanol is rapidly increasing
Automotive ethanol capabilities vary widely country to country, but most spark-ignited gasoline style engines will operate well with mixtures of up to 10% ethanol
Brazil is the world leader in ethanol fuels
Ethanol fuel is produced from sugar cane in Brazil, which is a more efficient source of fermentable carbohydrates than corn as well as much easier to grow and process in the tropical climate
“E” Numbers
Ethanol fuel mixtures have "E" numbers which describe the percentage of ethanol in the mixture by volume, for example, E85 is 85% ethanol and 15% gasoline
Low ethanol blends, from E5 to E25, are also known as gasohol, though internationally the most common use of the term gasohol refers to the E10 blend
Gasohol
E10 gasohol is becoming more commonly found at gas stations in the U.S. (Tennessee is way behind)
As the “10” indicates it is made from a mixture of
gasoline (90%) and ethanol (10%)
Gasohol has higher octane, or antiknock, properties than gasoline and burns more slowly, more cooler, and more completely, resulting in reduced emissions of some pollutants
UT & Switchgrass
The UT Biofuels Initiative has started testing the use of switchgrass, which is believed to offer a greater ethanol yield than corn in a temperate climate, such as in Tennessee
The project represents the culmination of years of corporate research and development and a highly touted $40.7 million investment from the state of Tennessee to build a plant for demonstrating technology developed by DuPont Danisco Cellulosic Ethanol
Alternative Energy Sources
Most of the world still relies very heavily on fossil fuels, but slowly but surely, attention is being diverted to alternative energy
Energy use in the future will not be dominated by a single source
The most important aspects of most alternative energy sources is that they promise clean, pollution-free energy